Torsion spring replacement
The contractor measures the door and existing hardware, selects the correct wire size and length, then winds the new torsion spring or springs to balance the door properly.
Spring repair · Palm Bay
Broken Garage Door Spring Repair
Describe what happened once and get connected with a local Palm Bay contractor who replaces broken springs and gets your door working safely again.
✓
Describe what happened once
✓
Connect with a local contractor
✓
You decide what happens next
A door that will not lift
When a broken garage door spring stops the door
A broken garage door spring usually shows up all at once: the opener hums but the door barely lifts, the door feels unusually heavy by hand, or you hear a sharp bang from the garage and the door won't move afterward. Springs carry most of the door's weight. When one breaks, the opener is suddenly trying to lift a load it was never designed to lift on its own.
In Palm Bay, garages get used constantly, and heat and humidity are hard on metal over time. Springs also take a beating in coastal Florida air, especially if the garage faces wind-driven rain or stays damp. If your door is stuck closed with a car inside, or stuck open and you can't secure the home, the safest next step is to get a contractor involved rather than forcing the door.
What you can do right now:
- If the door is partway open, avoid walking under it. A door with a broken spring can drop.
- Don't keep pressing the wall button. A strained opener can burn out or pull on the top section of the door.
- If you have a manual lock engaged, which is common on older doors, leave it alone until a contractor looks things over.
Palm Bay Garage Door is a referral service. When you call, you describe what the door is doing—or not doing—and what type of spring setup you have if you know it. We connect you with a local contractor who handles broken spring repair and replacement on residential garage doors. For other door issues that sometimes show up at the same time, the broader garage door repair service is the place to start.
Spring service details
What a spring contractor typically handles on this visit
Extension spring repair options
For doors with springs running alongside the horizontal tracks, the contractor replaces worn or broken extension springs and checks that safety cables are present and correctly routed.
Balance and lift check
A good broken spring repair ends with a balance test: the door should stay in place when lifted partway, without drifting up or slamming down.
Hardware inspection tied to spring failure
Spring jobs often include checking lift cables, bottom brackets, center bearing plates, end bearings, and rollers for wear that can cause uneven lifting.
Opener strain review
When a spring breaks, openers can get overworked. The contractor may check the opener arm, trolley, and force settings after the door is correctly balanced.
From diagnosis to testing
How broken spring repair usually goes
Confirm the spring type and failure
The contractor identifies whether your door uses torsion springs mounted above the door on a shaft or extension springs along the tracks, then confirms what broke and why the door isn't lifting.
Measure for the correct replacement
Spring sizing is not one-size-fits-all. The door's height and weight, drum type, and existing hardware determine the right spring wire size, inside diameter, and length.
Secure the door and replace the spring
The door is clamped in place, tension is handled with proper tools, and the broken spring is removed and replaced. On extension systems, the contractor also checks pulleys and cables used with the springs.
Set tension and balance the door
For torsion spring replacement, the spring is wound to the correct torque and set screws are secured on the shaft. The door is then tested by hand for smooth, even travel.
Reconnect the opener and test operation
Once the door is balanced, the opener is reconnected and tested for normal opening, closing, and reversal behavior. The contractor can also point out any sections or hinges that were stressed while the spring was broken.
One call starts the spring repair conversation.
If the door feels heavy, won't open, or you heard a bang from the garage, describe what you're seeing once and get connected with a local Palm Bay contractor who handles garage door spring replacement.
Springs and balance
Spring setups contractors see around Palm Bay
Common questions
Broken spring repair questions Palm Bay homeowners ask
How can I tell if it's a broken spring and not the opener?
If the door feels extremely heavy when you try to lift it manually, a broken garage door spring is a likely cause. With the opener disconnected using the red emergency release cord, a properly balanced door should lift smoothly and stay near waist height without dropping; if it wants to slam down, the spring system is not carrying the weight.
Is it safe to open the garage door with a broken spring?
It is not safe to force the door open with a broken spring because the door can drop and the opener can be damaged. A contractor can secure the door, handle the stored spring tension with the right tools, and restore proper balance before the opener is used again.
What's the difference between torsion spring replacement and extension spring repair?
Torsion springs mount above the door on a steel shaft and lift by twisting; extension springs stretch along the tracks and lift through pulleys and cables. The replacement parts, safety checks, and adjustment method are different, so the contractor typically confirms which system you have before quoting the work.
Will the contractor replace one spring or both?
On two-spring torsion systems, contractors often recommend replacing both because springs of the same age tend to cycle out around the same time and an imbalance can affect lifting. The contractor you speak with can explain what your door has now and what replacement approach makes sense for your situation.
What will the contractor need to know when I call?
The contractor will usually ask whether the door is stuck open or closed, whether you heard a loud bang, whether you have one or two springs, and the door size if you know it—common residential heights are 7 or 8 feet. A photo of the spring area above the door for torsion systems or along the track for extension systems can also help the contractor bring the right parts.
What gets checked besides the spring during a broken spring repair?
A careful spring job includes checking lift cables for fraying, drums for wear, bearing plates, hinges, and rollers, plus confirming the door is level on the tracks. In humid Florida garages, contractors also watch for rust at the spring cones and on the shaft because corrosion can affect adjustments and hardware grip.
How does Palm Bay Garage Door help if I'm not sure what broke?
You can describe the symptoms and what you noticed, such as a heavy door, opener strain, a crooked door, or a bang sound. Palm Bay Garage Door connects you with a local contractor who handles garage door spring repair in Palm Bay. You talk to the contractor directly about what they found and what you want to do next.
Get the door checked before you force it
A broken spring changes the whole load on the door and opener. Describe what happened once and get connected with a local Palm Bay contractor who can inspect the spring setup, explain torsion vs. extension options, and restore safe operation.